Check the appropriate box below if the Form 8-K filing is intended
to simultaneously satisfy the filing obligation of the Registrant under any of the following provisions (see General Instruction A.2 below).
Indicate by check mark whether the registrant is an emerging growth
company as defined in Rule 405 of the Securities Act of 1933 (§230.405 of this chapter) or Rule 12b-2 of the Securities Exchange
Act of 1934 (§240.12b-2 of this chapter).
If an emerging growth company, indicate by check mark if the registrant
has elected not to use the extended transition period for complying with any new or revised financial accounting standards provided pursuant
to Section 13(a) of the Exchange Act. ¨
To the extent required, the information set forth below in Item 7.01 of this Current Report on Form 8-K is incorporated herein by reference
in its entirety.
On
November 19, 2026, ClearSign Technologies Corporation (the “Company”) issued a press release announcing the results of
operations for the quarter ended September 30, 2026 (the “Financial Results”). The press release is furnished as Exhibit 99.1
to this Current Report on Form 8-K and is incorporated by reference in its entirety into this Item 7.01.
Also
on November 19, 2026, the Company held a conference call discussing the Financial Results and other business related information.
A transcript of this conference call is furnished as Exhibit 99.2 to this Current Report on Form 8-K and is incorporated by
reference in its entirety into this Item 7.01.
The
information furnished with this Item 7.01, including Exhibits 99.1 and 99.2, shall not be deemed “filed” for purposes of Section 18
of the Securities Exchange Act of 1934, as amended (the “Exchange Act”), or otherwise subject to the liabilities of that section,
nor shall it be deemed incorporated by reference into any other filing under the Securities Act of 1933, as amended, or the Exchange Act,
except as expressly set forth by specific reference in such a filing.
* Filed herewith.
** Furnished herewith.
Pursuant
to the requirements of the Securities Exchange Act of 1934, the registrant has duly caused this report to be signed on its behalf by the
undersigned hereunto duly authorized.
Exhibit 99.2
Transcript of
ClearSign Technologies Corporation
Third Quarter 2026 Financial Results
November 19, 2026
Participants
Matthew Selinger - Investor Relations, ClearSign
Technologies Corporation
Jim Deller - Chief Executive Officer, ClearSign
Technologies Corporation
Brent Hinds - Chief Financial Officer, ClearSign
Technologies Corporation:
Analysts
Sameer Joshi - H.C. Wainwright
Peter Gastreich - Water Tower Research
Presentation
Operator
Good day, everyone, and welcome to ClearSign Technologies’ Third
Quarter 2026 Earnings Conference Call. At this time, all participants are placed on a listen-only mode, and we will open the floor for
your questions and comments after the presentation.
It is now my pleasure to hand the floor over to your host, Matthew
Selinger, Investor Relations at ClearSign. Sir, the floor is yours.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Good afternoon, and thank you, operator. Welcome, everyone, to the
ClearSign Technologies Corporation third quarter 2026 corporate update call. During this conference call, the company will make forward-looking
statements. Any statement that is not a statement of historical fact is a forward-looking statement. This includes remarks about the company’s
projections, expectations, plans, beliefs, and prospects. These statements are based on judgments and analysis as of the date of this
conference call and are subject to numerous important risks and uncertainties that could cause actual results to differ materially from
those described in the forward-looking statements.
The risks and uncertainties associated with the forward-looking statements
made in this conference call include, but are not limited to, whether field testing and sales of ClearSign products will be successfully
completed, whether ClearSign will be successful in expanding the market for its products, timing of customer orders and our ability to
convert proposals into orders, delays, holds, or cancellations of customer projects, the performance of our products in the field and
related warranty costs, our reliance on original equipment manufacturers and other third parties, our ability to obtain additional financing,
and other risks that are described in ClearSign’s filings with the SEC, including those discussed under the risk factor section
of the annual report on Form 10-K for the fiscal year ended December 31, 2025, and on our quarterly report on Form 10-Q
for the quarter ended September 30, 2026, and of course, our subsequent filings.
| Transcript Provided by |
| |
 |
| |
| 1 |
Any estimates we discuss today regarding our pipeline or potential
future orders are forward-looking statements and are not guidance. Except as required by law, ClearSign assumes no responsibility to update
these forward-looking statements to reflect future events or actual outcomes, and does not intend to do so.
So, on the call today with me are Jim Deller, ClearSign’s Chief
Executive Officer, and Brent Hinds, ClearSign’s Chief Financial Officer.
So, with that, I am going to turn the call over to Jim Deller.
Jim?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Thank you, Matthew. As always, I would like to thank everyone
for joining us on the call today and for your continued interest in ClearSign. Like our most recent calls, we will use a Q&A format
for this session. Some of you have sent in questions ahead of time. We did assimilate those questions into the questions that we will
cover today. For the call today, Matthew will lead the question-and-answer session, where we will go through the different business units,
much like our previous calls. Many of you have seen this, but you can send in questions ahead of time to our investor relations at mselinger@firmirgroup.com.
We will start with Brent Hinds going over the company financials for
the third quarter of 2026. Brent?
Brent Hinds - Chief Financial Officer, ClearSign Technologies
Corporation:
Thank you, Jim, and thank you to everyone joining us here today. Before
I begin, I would like to note that our financial results on Form 10-Q was filed earlier this week with the SEC.
With that, I would like to give an overview of our financial results
for the third quarter of 2026. For the third quarter of 2026, the company recognized approximately $712,000 in revenues compared to approximately
$1 million for the same period in 2025. The year-over-year decrease in revenue was primarily attributable to product mix. While the product
mix during the quarter resulted in lower reported revenue, it generated meaningful improvement in gross margins. As discussed in our Q2
conference call, we entered into a licensing arrangement with an OEM heater manufacturer to build three M Series midstream burners,
and we successfully fulfilled our obligations under this arrangement during the third quarter of 2026.
Our third quarter gross profit margin was approximately 55.6%, which
is an increase of almost 20 percentage points over the prior comparable period’s margin of 35.8%. This year-over-year improvement
in gross margin was primarily driven by our licensing arrangement with an OEM heater manufacturer. We believe licensing arrangements like
this further diversifies our go-to-market strategy, and we expect to continue pursuing such arrangements to further expand our revenue
channels. We also believe licensing arrangements like this will bolster our overall gross margin and help us achieve our overall long-term
company gross margin target of 40%.
Now moving on to the full P&L. Our net loss for the third quarter
decreased by $361,000 compared to the same period in 2025. The decrease in our net loss was predominantly driven by a $601,000 decrease
in general and administrative expenses, offset by a $233,000 decrease in other income. Our G&A expenses decreased predominantly due
to a one-time non-cash expense in the prior period related to the vesting of restricted stock units issued to our former directors. Other
income decreased predominantly because our Department of Energy grant completed in May of 2026.
| Transcript Provided by |
| |
 |
| |
| 2 |
Let us shift our focus to cash. Our net cash used in operations for
the third quarter of 2026 was approximately $1.3 million compared to approximately $1.8 million for the same period in 2025. This improvement
was driven predominantly by timing of customer cash collections. As of September 30, 2026, we had approximately $10.3 million in
cash and cash equivalents. As of September 30, 2026, we had approximately 6.8 million shares of common stock outstanding.
With that, I would like to turn the call over to Matthew Selinger.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Brent, thank you for the financial overview and, Jim, thank you for
joining me today here. I would like to start the call with a brief overview of ClearSign, Jim, what we do, how we do it, for any new investors
and, after that, I think we will dive into the product lines and company developments.
So, with that, Jim, could you summarize briefly or high level, what
does ClearSign do?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes, certainly. So really high level, right? We have unique IP and
some leading engineers for the company. In essence, we provide a technologically advanced solution to enable energy companies to efficiently
meet their clean air emissions obligations. So our clients are large oil refiners, petrochemical companies, midstream gas companies, generally
companies in the energy business, right? As part of their production, they burn fuel gases, right, natural gas or gas blends to make their
processes work, whether it is heating up oil to break it down or whatever. As part of that combustion process, they make toxic gases,
and we are primarily concerned with NOx emissions. These are nitrogen oxides. These gases are highly regulated. They have to operate within
them to stay within their permits. They are controlled by the local air regulators and the traditional technology that allows them to
get down to the latest levels we are seeing in California and Texas is they call a selective catalytic reduction unit. This is a very
expensive piece of equipment that has to be built into the back end of their heaters, and then it has to be supplied with ammonia to operate.
With our unique technology, we can provide special burners that essentially do not make the NOx emissions in the first place.
We have all had kids. You might compare it to your kids and explain
to them, hey, it is much better not to make the mess in the first place than to have to go to the expense of cleaning up afterwards. To
put some numbers to that, talking to customers from one of our projects that we have to date, for their project, their estimate to put
in an SCR and solve their problem that way was $15 million. Using the ClearSign burners, we believe their total cost to be in the region
of $5 million to $10 million. So we are looking at an 80% cost savings for that client. If you look at a large refinery, they have probably
got 40 to 50 heaters on that refinery that savings will add up to hundreds of millions of dollars for that refinery if they apply it across
the site. It is a very meaningful opportunity for our customers.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
All right. So again, I know our technology has been referred to
before kind of maybe as a simple but elegant solution. Like you said, again, we basically have a, call it a better combustion, better
flame that does not then produce these emissions in the first place.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes.
| Transcript Provided by |
| |
 |
| |
| 3 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. Fantastic. That sounds simple enough. Then how does ClearSign
go about getting these solutions into the market?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. This has been a key part of the strategy of ClearSign, certainly
since I joined. We have a very unique technology, obviously. We manage our sales. We have significant engagement with customers. But to
provide burners in this industry, there are some what would be typical barriers to entry. You have got to be able to demonstrate your
equipment operating at full scale. Plants like oil refiners require you to manufacture equipment in shops that they have accredited themselves.
Setting those up is a very cash-intensive business. We are judicial with our investors’ money. We understand that is how we exist
today. So we formed a strategy we call asset light. Essentially, we focus on the IP, and we have formed collaborative relationships with
other companies that have the infrastructure we need that allows us to benefit from their infrastructure without that being either a capital
cost or an ongoing cost for ClearSign.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Great. So again, simplifying again, you are basically leveraging existing
businesses or infrastructure to bring kind of our advanced technology solutions to market.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. All right. Well, let us go ahead then and move, if you do not
mind, into the product lines. Does that work?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Certainly. Yep.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
I think it makes sense to start with process burners here. We have
a growing number of installations in the field, but in particular, we’ve been talking about a 26 burner order going to a Gulf Coast
facility of a petrochemical customer for some time and then this installation was slated to start at the end of October and be operational
here in this month. I think everybody’s waiting, especially our investors that follow us. How is this going?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Everyone is waiting for this, yes. It’s going great. You said
the burners were due to install October. That went absolutely smoothly, and they’re due to start up in November, and I believe we’re
ahead of schedule on that timeline. It’s looking really good. I think we’ll be done within about a week.
| Transcript Provided by |
| |
 |
| |
| 4 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I’m really looking forward to having that done.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
All right. Again so how -- on this installation, either like or unlike
others, I mean, how are we going to be able to kind of claim or I guess signal a victory to the market and maybe an industry?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. In terms of the event, if you like, this is different. This is
a big, sophisticated heater on a global chemical company. In these big installations, the equipment is monitored on a continuous basis.
They have a system they call, known as CEMS, Continuous Emissions Monitoring equipment, and that takes continuous measurements of the
emissions going out the stack and actually live streams it down to the air board and, of course, to the operators and to the site there.
Those analyzers are calibrated and certified by the local air board, and that is the formal measurement. So we will be watching, as will
everybody else, watching those numbers to ensure that they are down below the permit and the guaranteed levels at the end of this project.
So that will be the success. And for anyone looking at ClearSign Technologies, we have been focused on getting this project done and excited
about it for so long that you will see LinkedIn announcements and in time, presentations and other materials. But the data from those
emissions monitors will be the metric, if you like, the event that everyone’s looking for, for the technical success of this installation.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Right. You said yourself, we put a lot of weight in the startup. So
what do you think this means then for ClearSign Technologies’ prospects going forward, and how are we going to, in a sense, leverage
this?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I think this is -- I mean, all the time we’ve said that this
is huge or really meaningful. We are talking and have been talking for a long time to heater companies and importantly, the lead engineers
of the major refiners needing to comply with local emissions regulations. They understand the value of our technology. They understand
what we do. Many of them have been to see our burners at the test furnace. The only thing they’re waiting on is having a place to
go see it. It’s almost like test driving a car or speaking to someone that’s running it so they have the confidence to recommend
this product for themselves. We’ve had literally the words of one of the leading engineers from a major refinery say, I want
to be the first, second person to use your burners. This reference is a major installation on a global chemical company in the middle
of our biggest market down on the Texas Gulf Coast. It has been engineered by the premier heater engineering company in the country, Birwelco.
While we cannot name the customer or the job site publicly, within conferences like the American Petroleum Institute that we go to, people
are aware of this project. They have been watching it. So this is a really big deal for the place. I am very excited to have this done.
| Transcript Provided by |
| |
 |
| |
| 5 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
All right. It is obviously a big catalyst. Investors are going to want
to know, Jim, I guess, what are the next actionable items internally? Are we just going to let this kind of trickle out to the market?
How are our prospects going to know about this?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. There will be many events. Key among these, I was down at
the American Petroleum Institute last week and already talking to the lead engineers on our refiners. They are aware that this project
is starting up. When we get this project operating successfully, I personally will be making phone calls to those people explaining
what we have done, trying to talk them to come and see it, try to set up arrangements for them to witness it on the job site. I think
my arrangements. Beyond that, I am looking forward to conference presentations, magazine articles. Please ask anyone to follow us
on LinkedIn. We will be putting information about this out publicly. So this will be a multi-layered approach, but it will start with
these one-on-one phone calls. I mean, there are certain key people in the industry that have talked to us about all the projects they
are waiting for.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I mean, they are going to be called and talked to. They’ll be
engaged in conversations as soon as we can get them on the phone.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. Well, thank you. That’s what investors are going to want
to hear. Let’s come back, and you did talk about a proposal pipeline, but I’ll come back to that later, I think. Let’s
talk about other projects, right? We’ve got another notable project in process, a 32-burner order, and this is slated for California.
What’s the status of this project today?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. This one is going really well. In the big picture, the phase
that we’re at, we had a detailed engineering and testing phase that is almost down to completion. It’s pretty much done with
the point of discussing the witness date with the client and from there, we’ll be moving on to the fabrication of the burners to
ship the first half of the burners out to the job site in California. The plan is to get those out and get those up and running, and then
to roll in and supply the second half. Just to, if I can, to talk a little bit more about this one, this project’s been in the test
furnace a bit longer than the standard two or three weeks.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah.
| Transcript Provided by |
| |
 |
| |
| 6 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
The reason is, this is a new configuration of our Gen2 technology platform.
When we developed that Gen2 burner, we described it as a technology platform that’s adaptable and usable for different installations.
This is the burner in that flat flame configuration, right? It’s the first one with a flat flame. This expands our market to get
us into a new section of the heaters on refiners, often the larger heaters. As we’re going through this, we’re adapting the
flame to be optimized in that heater. From my perspective, though, additionally why we’re putting a lot of effort into this is I
see this as a stepping stone to get into new markets for ClearSign. But we have talked in the past, and I am sure we will talk again about
high temperature applications, downfired reformers often for hydrogen production, ammonia production, things like that, and also for ethylene
furnaces. The ethylene furnaces are flat flame burners. The burner we have today is not suitable as it is for ethylene furnaces, but it
is a significant step in that direction and I think sets us up well to get engagement and start formally pursuing that expansion of our
business.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. I am just going to back up and maybe unpack this. So, obviously,
and we have talked about this in other calls, but the implication here, because of this different configuration, right, is that, A, it
is a different implication for process burners, which we are already going through on this project, right, and demonstrating we can utilize
this in a different type of-
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yep.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yep. But beyond that, in particular, this means, as you mentioned,
this could enter us into other markets. You mentioned downfired reformer, ethylene, and these are massive markets, as you have talked
about in the past, right. If you could just give a little color, the size of these in the market and the heaters.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. From my experience, well, typically the ethylene business for
a burner manufacturer is as big as the refining business. So it will double our market size that in itself. The downfired reformers, these
units can be up to over 200 burners in a single.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Massive.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Again, both of these are very big burners. The great thing is when
you’re making burners, whether it’s ethylene or multiple furnaces side by side, or the downfired reformers, you’re building
hundreds of burners exactly the same.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. Okay. This could be looked at maybe a stair step towards that.
What else would be needed for ClearSign to go into those markets?
| Transcript Provided by |
| |
 |
| |
| 7 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. There is significant work that will go into developing the burners.
We call these high-temperature applications for a reason. These furnaces are very hot. There will be research and development significant
to develop these products. Now, going into this kind of a program, you really want to do that with a customer partner who is all into
the projects. You make sure you’re developing the right product, you’re developing it as this customer needs it, and then
at the end of the project, when you have it, that means you’ve got an installation lined up to put that burner into service and
to demonstrate it and essentially to launch the product line. So there’ll be a number of pieces that go into getting these projects,
but for me, we really want to get a customer partner engaged in this development.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yep
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
So we can be assured of having a properly developed product at the
end. We want the input, and we want a home for that first installation.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Has the company had any conversations with potential partners?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. I mean, this has been part of our long-term strategy. We get the
process burners done first. No, we have been actively talking with various people and entities about this project. We don’t have
anything formal arranged at this time, but it is a project that we are actively working on.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. Well, it’s exciting. Let me get back to process burners,
if you don’t mind. We also have announced a 36-burner order, and this was going to Texas as well. But we mentioned in the last call,
this one’s been delayed a bit. Is there any change of status?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
There is not. I mean, again, just to iterate for anyone, we do not
believe, and we have been told this has nothing to do with ClearSign. It is due to internal organizational changes within the client.
For that, we also do not have any updates. I just look forward to getting this project back on track.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. Just a few weeks ago, it was actually the last day of the quarter,
the third quarter, September 30, you announced along with Kern Energy, that ClearSign had been selected for the DOE Industrial Technology
Validation Program for a grant there. Could you give a little more color on this?
| Transcript Provided by |
| |
 |
| |
| 8 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. It is a nice project, and it is a great initiative from the DOE.
This is a joint project between us and our long-term customer, Kern Energy. Basically, it is a DOE-funded project to pay for the installation
of one of our latest Gen2 process burners into a heater on the Kern Energy site. It is going to be a fast-term project. The DOE will provide
the money. Kern will place a full purchase order on ClearSign with that DOE money. It is an order for us. It gets another reference out
in the field. It is, yeah, a great little project for us.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Great. I do want to highlight, though, while we are not waiting on
this, quote, validation, right, this will be an additional validation or data point, right? This product is already out.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
We have many, many quotes using this burner technology. We demonstrated
it to industry. But hey, extra size, having the equipment up and running in addition to the order and the revenue, it is --
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
A great reference.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
A win for ClearSign and a great support, a long-term customer like
Kern.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Great. So in terms of looking at the process burner product line, what
do the prospects look like? We talked about the proposal pipeline in the past. How is that still looking today?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. I mean, these prospects are changing rapidly as we complete this
project down in Texas. So this is really exciting times for us. We have talked in the past a lot about the one customer who has identified
10 heaters they want us to look at. There are other clients that we are installing burners into that have referenced more heaters they
want to look at. When those are done, there are other refinery heaters resulting from the demonstration and other sales activities that
we have quoted to. There are a lot of proposal opportunities and clients that we are in discussions with about that heater, very much
focused on this Texas startup to give them confidence. So this is really exciting. Just the timing right now is a really big deal. Yeah,
we are thinking in about a week, we will have that Texas site ready to talk about.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. When you say heaters, obviously you mentioned again, one company
with 10 heaters or so. I think we mentioned this in the last call. A good number, is it an average number of burners, saying 10 burners?
I know they could be 10 to 30, something in that ballpark.
| Transcript Provided by |
| |
 |
| |
| 9 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I mean, that is fair. There are some smaller heaters with three to
five burners. But if you look at the orders we have in-house right now, there are 26 we are starting up down in Texas. There are 32, the
flat flames we are sending out to California. The one down in Texas that is temporarily on hold was 32 burners. Yeah, a heater is typically
going to be, when we look at revenue numbers, $2 plus million for ClearSign.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. Great.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Well, let’s turn to the M Series then next, if you don’t
mind. This is the midstream product, and it seems that this has been growing into a steady stream of business. We had five orders in Q3,
two so far already in Q4. Where is this business coming from?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I mean, geographically, these orders are all coming out of the Permian
region, West Texas area.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
But we’ve shipped, is that correct, burners to other geographies?
And then are you seeing other interest from other places as well?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
We are. We have burners, yeah, in Oklahoma here at Nexus, one in New
Mexico. Going into energy installations, we have quotes into the Marcellus area of the Northeast region. We have quotes into Canada. So
we are seeing a much wider interest. The recent orders that we’ve processed, the five last month and the two this month, are all
going down to the Permian. In terms of if we’re going to go and set up a presentation somewhere, the big market right now for growth
is coming out of that Permian area, which is having these burners going down there for reference right to that region also is very powerful.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
And new heaters too.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. So key, I think differently from other industries, the midstream
area is growing rapidly. I believe the growth was over 20% last year. This is for gas for export. It’s for gas that’s going
into increased utilization. If you think of all these data centers we keep hearing about, they need gas to generate their electricity.
So, there’s a massive demand for gas and the growth of midstream industry. So, these -- in fact, I believe all of these recent
orders are new heaters going down to expansion of the assets down in the Permian region.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
And these orders seem to turn a lot quicker. Is that right?
| Transcript Provided by |
| |
 |
| |
| 10 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. Certainly much faster than the process burners. The strategy we
set this up was these are standard products. They are designed to be repeated and off the shelf, and we have got a sufficient frequency
now, and our clients have standard heater sizes so that the drawings for these orders and the engineering is already done. So, we get
an order, our vendors already have the drawings for these recent sizes, we are able just to produce more burners. So, we get to the point
of achieving the efficiency that we had envisioned when we formed the strategy for this product line. So, with that, the timing, we can
turn these orders now in about three to four months once we see the order.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. I mean, I think we saw that. I think we saw orders, as Brent
mentioned, we had orders in Q2, obviously shift and booked in Q3. These are going to be much quicker. Theoretically, we could fulfill
one within the same quarter. I don’t want to get aggressive. When you talk --
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. If we receive it in the first week of the quarter, it is feasible
for us to turn it in that quarter. The two we have received this month, the company, the client has a request date. They will be shipped
out in Q1 2027.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
You alluded to that in the last press release, if I am not mistaken,
correct? Talking about those said efficiencies in the manufacturing process.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. I mean, for us, the consumption of our resources is minimal now.
We have got the work done. We obviously place the order overseas for inspections and shipping and things like that, but the engineering
of the design work is already done.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. Okay. Let’s talk some numbers, Jim. What’s the dollar
range that these burners are selling for?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes, these are a wide-ranging product. In dollars from our standard
sizes, they run from about $50,000 up to about $250,000 per burner. To put the current orders in perspective, most of these are a large
size, they’re not the largest, but they’re running in the $180,000 range.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. That’s great. And so what sort of run rate do you think
was obtainable that we could see in this product line?
| Transcript Provided by |
| |
 |
| |
| 11 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I think we’ve got some data to give us confidence. Last quarter,
we ran about five burners. We’ve already got two in for this quarter. The quarter’s not over yet. My goal for these products
down in the Permian Basin, when we get these up and running, is to just be the go to 9 PPM midstream burner supplier. If we get them proven, I
think that’s very achievable. I see no reason we shouldn’t expect to at least maintain that five per quarter run rate of around
about 20 per year.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. Fair enough. All right. Let’s move over to flares, if you
don’t mind. What is the latest development on the flare product line?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. This is similar, really across all of our product lines. We’ve
talked about this. This year has been getting -- we standardized, we got our products worked out, and getting the big installations out
running. So, the Gulf Coast process burners like that, but we’ve actually got great M Series out, but getting those out, established
in the industry, and it’s the same for flares. Our biggest flare system is out in California, it’s just about complete. It’s
scheduled to start up by the end of the year. This will be a great reference because we know that that client has permits in progress
that reference ClearSign Technology. We believe they’re waiting for this startup to proceed with other flares, just really the same
situation we are with the others. So, this startup’s going to be very significant for us. We’ve also talked about taking the
flare as a burner product and turning it into a full million-dollar system. This is a $1.5 million project of a complete flare system
that ClearSign is now starting up in California and really showing, hey, we are a flare supplier.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. So, similar then to the, like you said, the 26-burner order,
kind of demonstrating this full system, you believe will be a catalyst as well.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. I mean, this is a big, very credible flare in the industry. Getting
this up and running, and what’s rare amongst the flares is a flare that can actually meet a measured emissions permit for NOx is
going to be very special in the market. This is a big deal.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Sure. In this product line, I mean, it’s not going to turn
as quickly as, let’s say, the M Series, right? Do you have a target or a desirable sell rate, you think, over a year on these?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah, desirable is a different thing, actually.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Sure.
| Transcript Provided by |
| |
 |
| |
| 12 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I think seeing what we’re seeing, right, this is a steady local
product, predominantly in California. There’s been a little bit of interest in other places. I think it reasonable to look at three,
possibly four per year as a runway based on what we’re seeing at this time. This one will be lumpy. The nice thing with the midstream
is that there’s enough volume now and they’re fast enough, I think we can start to see a smoother supply of those. Only
the flares are going to be on an individual basis. It may not be so steady. I think for long-term runways, that is probably a fair expectation
based on the technology and the markets where they are today.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. I want to bring all the product lines together, if you do not
mind, Jim, because we are nearing the end of the year. But are there milestones we can look for between now and the end of the year, or
do we jump to 2027?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
No. We talked about some of these, but Kim, hopefully within a
week, we are going to be making phone calls about that Texas project. By the end of the year, we will get the flare started up. The way
the midstream industry has been performing being productive for us. I am hoping we are going to get some more midstream orders before
the year is out. Within the more strategic long-term developments that we are making at ClearSign, there are, as I have alluded to, there
are conversations we are having trying to put the plan together for moving into things like the high-temperature burners. There is certainly
internally, whether it is something we are going to announce or not, but I am certainly looking to make progress on those projects before
the year end as well.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah. There is a lot.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
We have got a lot to do this year. We have not finished yet.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay. That is great. How about -- thank you for that. How about 2027?
Let us talk about next year. I know you spent time to talk about the pipeline, and we put some pieces together here in this conversation,
but what do you think 2027 could look like for ClearSign?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I am excited about next year. I mean, we have really gone through this
year focusing on getting these major startups and references out, operation in the field, talking about those. But we have brought that
together, and this year we are right in the final stages of wrapping that up. Next year is the time to get the benefit of those. We will
be out promoting the Texas installation, having that great reference in place. I am looking to bring in process burner orders next year.
| Transcript Provided by |
| |
 |
| |
| 13 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Yeah, converting.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
That reference in place, bringing the people in. Yeah, converting those,
let’s get moving on those projects. I am looking for process burner orders. I am looking to follow on from the flare installation,
and I am really excited about the midstream, getting these burners that we have seen going out to midstream. Many of those are scheduled
to start up in Q1, some in Q2 that will give us functioning burners down in the Permian Basin in these big installations. I said I want
to be the go-to supplier for those burners. I think we have got a fantastic technology in the M1 burners. I do not want anyone to have
any questions why they should not just order them from us. I am really looking forward to developing a steady stream of M Series burners.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
It would be safe to say that 2026 was really kind of, lack of a better
word, establishing product line, and 2027 would be converting, conversion to those?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Right, that is a high-level look. That is what I am saying, that we
have truly talked about that, right, getting these major installations focused on developing technology, the demonstration of the Gen2
burner early in the year, focusing on the startup of the Gulf Coast, which is occurring as we speak. Yes, I think that’s we’re
really looking forward to getting out and using those references to validate our technology and start to give our customers the confidence
to move forward with their promotion.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Well, with that, let me ask you this then, Jim. How is the ClearSign
team doing? What’s the internal sentiment?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
They’re excited. I mean, the more we’ve got going on and
the work they’ve -- so if you just look back over the last month or two months, we’ve had a team down on the Gulf Coast site
going through the installation, checking that out, going through the startup with the operators, working with the client and the log with
the engineering company. At times, that’s been around the clock, so we’ve truly had a team down there. At the same time, we’ve
been running multiple burner tests at Zeeco. Our engineering team, we have a lean team here. We’re asset light. Everyone wears many
hats. They really dig deep and do what they’ve got to do. We have Brent and his finance team, and that have been out promoting midstream
burners at a midstream event, showing off their amazing sales skills. We’ve truly had all of the company doing what has to be done.
We’re very careful within the company to have frequent weekly communications to keep everyone up to speed on all of our projects,
what we’re doing, where we’re going as a company. I believe everyone’s really excited right now. They’re seeing
the success that we’re getting using from Texas. We’re seeing the steady stream of midstream orders coming in. Guys lined
up waiting to go and start the flare up out in California. Yeah, people are excited here. I mean, they’re working hard, and I really
appreciate that.
| Transcript Provided by |
| |
 |
| |
| 14 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Did I hear you correct, saying that even Brent was out on the sales
calls?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes, Brent and the whole sales team. Everyone was out. I think the
office was pretty much empty.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Was that, and I wonder, can I attribute the uptick in the gross margins
of this month to that, Brent?
Brent Hinds - Chief Financial Officer, ClearSign Technologies
Corporation:
Yes, you certainly can.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Okay, great. With that, there are no more formal questions from my
side. We are going to go and open it up, if we could, operator. We will take a pause here, but could we please open it up for question
and answer session?
Operator
Certainly. [Operator Instructions] Your first question is coming from
Sameer Joshi from H.C. Wainwright. Your line is live.
Q: Hey. Good afternoon, everyone. Thanks for taking my questions.
Just a few on gross margins and then order flow. The gross margins this quarter were better and I saw some reference to licensing arrangement
contributing to this. Can you explain that a little bit more?
| Transcript Provided by |
| |
 |
| |
| 15 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes, I can. Hey, Sameer, thank you for the question, first of
all. The licensing sales, we have had this as part of our plan for ClearSign really from the start as a part of the long-term strategy,
especially looking at scalability and how do we grow the business. It is also one of the benefits of product lines like the midstream
burners in this case, where we have standard products and we have clients that have the ability to manufacture their own burners. What
is special to ClearSign is the IP and the designs. In this case, we are able to provide the fabrication drawings to the client on a licensing
basis to give them the ability to fabricate their own burners. The benefits for the client are they get to manage the schedule. It obviously
saves them money because we are not paying a third party to fabricate the burners. For ClearSign, we make exactly the same profit, whether
it is a license sale or whether we are supplying the equipment. Of course, it is really been a win-win. The burners the client manufactured
look fantastic. I actually got to see them myself. We also put some photographs on LinkedIn. If anyone is following us, they have been
shipped down to the Permian Basin. So that went really well. We believe that the client will continue to purchase the burners for their
use in that way going forwards, and it has been a very good development for ClearSign, as you saw in the margins.
Q: Thanks for that. Should we expect, or let me ask it this
way. Are there other and more customers who are looking at this model, or it is only this one customer that is looking to manufacture
it themselves?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
We certainly expect repeat orders from this customer. I do not know
the plans of other customers. I would certainly be open to it. One of the criteria, of course, is they have to have the ability to manufacture
the burners themselves, but I am absolutely open to that. At this point, though, I have not had any other discussions about this
type of order with other customers. As I said, not at this time, but we certainly expect more orders in this manner from this one customer.
Q: Understood. Moving on to the M Series, I think it was
mentioned that you had five orders in 3Q and two orders in 4Q so far. Should we expect additional orders in 4Q that you may announce?
And I think you did address how 2027 looks for that, but how should we look at the order flow going into the end of the year?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah, absolutely. I mean, for us, the year is not over yet. We have
a lot of ongoing interest in the midstream burners, and one of the -- what actually makes these questions hard to answer specifically
is we have orders coming in that we have not specifically quoted, but we have sufficient -- we’ve given our customers sufficient
details of our standard burners that match their standard heaters, so they are now quoting their standard heaters, including our burners,
on opportunities that they’ve not necessarily told us about. We have actually received purchase orders out of the blue that we’ve
had to log into our system without having a prior quote. So given that, and given the conversations we’re having and the amount
of interest we’re seeing, I don’t have and I can’t make any guarantees, but yes, I am expecting additional
orders for M Series burners before the year is out, just given the nature of the industry and the rate that we’ve seen these
orders come in and just the general interest in the industry.
Q: Thanks for that. And just one last one, maybe for Brent,
and maybe I missed it in the commentary, but in addition to operating expenses being lower year-over-year, they were lower sequentially
as well. So was there an explanation given for the sequentially lower OpEx?
Brent Hinds - Chief Financial Officer, ClearSign Technologies
Corporation:
Yes. If you look in the MD&A section of the Q, you’ll see
the information. It’s really driven by the vesting of restricted stock units, which were non-cash and legal expenses as well; the
reduction from 2025 into 2026.
Q: Got it. Thanks a lot, and good luck.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Hey, thank you, Sam.
Brent Hinds - Chief Financial Officer, ClearSign Technologies
Corporation:
Thank you.
| Transcript Provided by |
| |
 |
| |
| 16 |
Operator
Thank you. [Operator Instructions] Your next question is coming from
Peter Gastreich from Water Tower Research. Your line is live.
Q: Thank you. Hi, Jim. Thanks for taking my questions, and congratulations
on the quarter. So it is good to hear the Gulf Coast burners are up and running, and, excuse me, nice to see the M1 orders keep coming
in. My first question is about DOE and Kern Energy. This program looks very interesting. Could you give us a sense of the size of the
opportunity and roughly when the burners would go in?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yes. This is a fast-turn project and a chance to get our new Gen2 technology
out into the field. We are able to address a particular need on this job site. So it is a single burner heater. There is a lot of engineering
involved in the order. I do not have the specific numbers to hand, but it is in the range of $500,000 to $750,000 from memory. I apologize
in advance if I am off with that, but from seeing the contract documents, I believe those numbers are accurate.
Q: Okay, great. Thank you. Oh, sorry.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. Sorry. You asked about the timing, and I will tell you my expectations.
We have completed the contractual details, which involve the representative of the DOE. We still have to work out the exact schedule with
Kern. My expectations are that we will receive the order from them early Q1. I do believe that they are still completing the permit, so
that is a caveat on that statement. With that, my best guess will be to complete the order somewhere around late Q3, early Q4 next year.
Again, those are estimates on my part. We have not worked out those details yet, so they may change, but that is my expectation for the
progression of that project.
Q: Okay, great. Thank you. Most of my detailed questions that
I had in mind have been answered, and I appreciate that. I just have a couple of bigger picture questions for you. So your team has talked
about burners that improve yield and uptime, not just cut the emissions. Are there customers that are generally starting to see ClearSign
as a way to improve plant profitability, and could that open additional markets that aren’t necessarily driven purely by NOx rules,
or is that not the right way to look at it?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
No, that, Peter, is exactly the right way to look at those opportunities.
Really what’s exciting is if we can improve the yield or improve the uptime for a client, we’re no longer just a cost for
compliance with emissions. We actually give them a significant return on their investment. The Texas project that is currently on hold,
unfortunately, was actually based on improving the uptime of that furnace as one of the primary drivers, so that was one project. That’s
been through the engineering. We completed the CFD modeling, and we were able to demonstrate those benefits to the customer at that phase.
Yes, it is something we’re pursuing, it’s something we’ve been able to demonstrate to that client. Going forwards, as
we’re able to show more and more to the industry what we can do, my expectation is that we will be able to capitalize on that ability
to a greater extent.
Q: Okay, thank you. Just a final question. So your CTO, Matt
Martin, he mentioned on our podcast a little bit ago that the M Series and the flare design went straight from computer modeling
to the field. Just want to ask, how does that change the cost and speed of bringing new products to market, and where does AI kind of
fit in with ClearSign?
| Transcript Provided by |
| |
 |
| |
| 17 |
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
First question is easy. The ability to design a burner in CFD to the
extent that we can create fabrication drawings and send it out to the field and have the success we’ve had on the M1 burner is a
game-changer. It typically takes probably an additional six months to a year when you’re going through the slow process of optimizing
a burner in a test furnace. Then you have to wait for mechanical changes to be made and then fire it up. In the computer, you can check
out different ideas. You can see what’s going on inside the burner and inside the flames. Then rather than speculating what changes
you need to make, you can actually see what’s going on and make surgical changes to optimize the process. For anyone who doesn’t
know this, the very first M1 burner was drawn from the output from our computer modeling program. It was put in a heater, and that design
has never been touched. That burner has actually demonstrated NOx down below 2 PPM, it is still out there running today and is the benchmark
for our entire M1 product line. This is one of the I’m just going to brag a little bit on our CTO, Matt Martin, the resources here
at ClearSign. We’ve been able to develop the computer modeling technology for combustion systems and burners, I believe, to
probably the greatest extent anywhere in the world, in my opinion but that has allowed us to bring technologies like this to market in
the speed that we have and to actually put them out in the field and have the success we’ve had both with the flare and the M Series burner.
To answer your basic question, it is hugely significant for ClearSign in the speed that we can bring not only new technologies, but also
adapt technologies for specific client needs and show them how those products will work modeled inside their furnace as part of our sales
or project validation process, so it is extremely powerful.
Q: Great. Thanks very much, Jim, and congratulations. I’ll
get back in the questions queue.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
I appreciate your questions, Peter. Thank you.
Operator
Thank you. There are no further questions in the queue.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
Operator, I am going to go ahead and read a couple, Jim, if you
do not mind from email.
.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Cool. Yep.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
I think you touched on this one, Jim, but the question is this. It
is clear that large-scale orders may have been held back while the old guard in the energy business waited to be absolutely sure they
would work as expected. So is this 26-burner startup likely to be a seminal event that opens the floodgates?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
We believe so. That is based on what we have been told from the clients.
Above everything else, they are waiting to see the technology running in somebody else’s heater. Yeah, the simple answer to that
is yes, we believe so. We are just excited to be able to get out and talk about it.
| Transcript Provided by |
| |
 |
| |
| 18 |
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
And Jim, in the past, the company, you have stated a kind of a break-even
number of 160 burners a year. Do you believe that is obtainable potentially next year, or is that a further target? What are your thoughts
there?
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Yeah. That number was based on $100,000 per, so $16 million run rate,
right? The math works out to get the company to break even. We absolutely have the line of sight in the pipeline to get to that number.
I mean, it is three or four process burner orders, a couple of flares, and then the runway with the M Series. It is a very pragmatic expectation
for the company. That is the one question we cannot guarantee is just the timing, right? But yes, the load is out there, the opportunities
are definitely out there.
Matthew Selinger - Investor Relations, ClearSign Technologies
Corporation
With that, Jim, there are no more questions. With that, I will
hand the call back to you if you would like any closing statements.
Jim Deller - Chief Executive Officer, ClearSign Technologies
Corporation
Great. Thank you very much. Hey, thank you, everyone. I really appreciate
you tuning in to this call and for your interest in ClearSign, and especially taking your time and giving us your time this afternoon.
We look forward to updating you regarding our developments and speaking with you on our Q4 and full-year call in April next year,
but we do not plan on being quiet with news on then. Please continue to check in on the websites. I do encourage you to follow us on LinkedIn.
Of course, when we have significant announcements, we will be putting press releases out in addition to that. So thank you very much.
Operator
Thank you. Everyone, this concludes today’s event. You may disconnect
at this time and have a wonderful day. Thank you for your participation.
| Transcript Provided by |
| |
 |
| |
| 19 |