STOCK TITAN

Resolution Minerals: 93.5m at 0.838 g/t gold downhole

Available on EDGAR Accepted by SEC EDGAR Learn about SEC filing dates
(Moderate)

Sentiment and the balance of points

Rhea-AI Sentiment reads the wording of the document, how positive or negative its language is on a 1 to 5 scale. The balance of points shown with the takes weighs what the document actually discloses, so the two can disagree, for example when a trial that missed its main goal is described in upbeat language.

Form Type
6-K

Rhea-AI Filing Summary

Resolution Minerals Ltd (RML) reported gold assays from three 2026 drill holes at Golden Gate North in Idaho. HH-GG26-035C returned 18.73 metres at 2.194 g/t gold; HH-GG26-033C returned 33.25 metres at 1.531 g/t gold, and HH-GG26-034C returned 93.52 metres at 0.838 g/t gold. These are downhole intervals and do not necessarily represent true widths; the company says the new intersections show continuity in the prospect’s south-central zone. It describes the mineralized zone as approximately 500 metres along strike, with an estimated true width of approximately 200 metres, and open to the northeast and southwest.

The completed 2026 program comprised 42 diamond core holes totaling 12,236 metres; assays remained outstanding for 30 holes. The company plans to calculate an initial mineral resource model after receiving the remaining assays, with a release anticipated in Q1 2027 subject to completion of the analysis. The reported significant intersections have not been verified by independent or alternative company personnel; the company plans select verification assays.

HH-GG26-035C gold interval 18.73 metres at 2.194 g/t gold Golden Gate North; downhole interval
HH-GG26-033C gold interval 33.25 metres at 1.531 g/t gold Golden Gate North; downhole interval
HH-GG26-034C gold interval 93.52 metres at 0.838 g/t gold Golden Gate North; downhole interval
Strike length Approximately 500 metres Golden Gate North, northeast-southwest orientation
Estimated true width Approximately 200 metres Golden Gate North mineralized zone
Vertical depth Approximately 300 metres Mineralization intersected at Golden Gate North
2026 drill program 42 diamond core holes; 12,236 metres drilled Golden Gate North and Golden Gate South
Pending assays 30 drill holes 2026 program
downhole lengths technical
"All reported intervals are downhole lengths"
Length measured along a wellbore from a specified reference point (typically the surface or wellhead) to a location down the hole; used to report how long a vertical, deviated or horizontal section of the well is, or how long an interval (for example a perforated or completed zone) extends along the borehole. It denotes the distance following the actual drilled path (measured depth) rather than the straight-line vertical distance, so reports should specify whether they mean measured depth, true vertical depth, or the length of a particular interval.
true widths technical
"do not necessarily represent true widths"
True widths refer to the actual difference between the highest and lowest prices at which a stock has traded over a specific period, reflecting its real price range. This measure helps investors understand how much a stock's price has moved, providing insight into its volatility and trading activity. A wider true width indicates greater price fluctuation, which can signal higher risk or potential opportunity.
hydrothermal fluids technical
"provided a pathway for hydrothermal fluids"
fire assay technical
"Au by fire assay and AAS"
Fire assay is a laboratory process used to accurately measure the amount of precious metals, like gold or silver, in a sample of ore or material. It involves heating the sample intensely to separate the metals from other substances, much like melting and purifying metal to determine its purity. This method is important to investors because it provides precise data on the metal content, helping to assess the value of mining operations or mineral deposits.
Fast-41 status regulatory
"both the Golden Gate Prospect and the Antimony Ridge have Fast-41 status"

FAQ

AI-generated questions and answers. How Rhea-AI works. Not financial advice.

What gold intersections did RML report at Golden Gate North?

The reported intervals include 18.73 metres at 2.194 g/t gold in HH-GG26-035C, 33.25 metres at 1.531 g/t in HH-GG26-033C, and 93.52 metres at 0.838 g/t in HH-GG26-034C. These are downhole lengths and do not necessarily represent true widths.

When does RML expect an initial mineral resource model for Golden Gate?

A release is anticipated in Q1 2027, subject to completion of the analysis, after the remaining drill-hole assay data are received. Assays for 30 holes from the 2026 program remained outstanding.

AI-generated analysis. How Rhea-AI works. Not financial advice.

See more from StockTitan in Google Search and AI answers. Adds StockTitan as a preferred source · opens Google
Add on Google

 

 

UNITED STATES
SECURITIES AND EXCHANGE COMMISSION

Washington, D.C. 20549

 

Form 6-K

 

Report of Foreign Private Issuer
Pursuant to Rule 13a-16 or 15d-16 under the Securities Exchange Act of 1934

 

Date as of: November 18, 2026

 

Commission File Number 001-43394

 

Resolution Minerals Ltd

(Exact name of Registrant as specified in its charter)

 

Not Applicable

(Translation of Registrant’s name into English)

 

Australia
(Jurisdiction of incorporation or organization)

 

Aharon Zaetz

Chief Executive Officer

Level 21, 91 King William Street

Adelaide, South Australia 5000
Australia

(Address of principal executive offices)

 

Indicate by check mark whether the registrant files or will file annual reports under cover Form 20-F or Form 40-F:

 

Form 20-F ☒        Form 40-F ☐

 

 

 

 

 

INFORMATION CONTAINED ON THIS REPORT ON FORM 6-K

 

On November 18, 2026, Resolution Minerals Ltd filed with the Australian Securities Exchange an announcement entitled “Significant Gold Intersections at the Golden Gate Prospect - Horse Heaven USA”, which announcement is attached as Exhibit 99.1.

 

This report on Form 6-K (including any exhibit hereto) shall not be deemed to be “filed” for purposes of the Securities Exchange Act of 1934 and shall not be incorporated by reference into any registration statement or prospectus under the Securities Act of 1933 except as may be expressly set forth by specific reference in such registration statement or prospectus.

 

1

 

SIGNATURES

 

Pursuant to the requirements of the Securities Exchange Act of 1934, the registrant has duly caused this report to be signed on its behalf by the undersigned, thereunto duly organized.

 

  Resolution Minerals Ltd
   
  /s/ Jaroslaw Kopias
  Jaroslaw Kopias
  Chief Financial Officer and Company Secretary

 

Dated: November 18, 2026

 

2

 

INDEX TO EXHIBITS

 

Item

   
     
99.1   Announcement, dated November 18, 2026, filed by Resolution Minerals Ltd with the Australian Securities Exchange.

 

3

 

Exhibit 99.1

 

 

 

SIGNIFICANT GOLD INTERSECTIONS AT

THE GOLDEN GATE PROSPECT - HORSE HEAVEN USA

 

LONG DOWN HOLE GOLD INTERSECTIONS WITH HIGHER GRADE INTERVALS GREATLY

ENHANCE GOLDEN GATE NORTH AS AN EMERGING GOLD DEPOSIT.

 

 

 

HIGHLIGHTS

 

Resolution has received strong gold assay results assays for drill holes HH-GG26-033C, HH-GG26-034C and HH-GG26-035C located at the Company’s emerging Golden Gate North deposit, at its Horse Heaven Project, Idaho USA.

 

Gold intersections for HH-GG26-033C include:

 

○234.8 metres (770 ft) @ 0.62 g/t gold (Au) from 18.3m downhole, including:

 

§33.3 m (109 ft) @ 1.53 g/t Au from 213.5m.

 

Gold intersections for HH-GG26-034C include:

 

○272.2 metres (893 ft) @ 0.55 g/t Au from surface downhole, including:

 

§7.4 m (24 ft) @ 1.26 g/t Au from 114.0m;

 

§23.1 m (75 ft) @ 1.38 g/t Au from 167.1m;

 

§32.1 m (105 ft) @ 1.01 g/t Au from 215.0m.

 

Gold intersections for HH-GG26-035C include:

 

○264.9 metres (870 ft) @ 0.59 g/t Au from surface downhole, including:

 

§19.4 m (64 ft) @ 0.90 g/t Au from 156.0m, including:

 

●6.1 m (20 ft) @ 1.39 g/t Au from 169.3m.

 

§39.0 m (128 ft) @ 1.53 g/t Au from 199.1m, including:

 

●18.7 m (61 ft) @ 2.19 g/t Au from 219.5m, and

 

●13.1 m (43 ft) @ 1.22 g/t Au from 245.7m.

 

These very significant gold intersections occur between drill holes that previously showed strong gold intercepts in HH-GG25-001C, HH-GG25-002C, and HH-GG25-003C to the north; and in HH-GG25-006C, HH-GG26-031C, and HH-GG26-032C to the south (ASX Announcements 28 October 2025, 3 November 2025, 17 February 2026 and 26 October 2026 respectively).

 

A continuous higher-grade central zone of the gold mineralisation at Golden Gate North is formed collectively by drill holes HH-GG26-033Cà035C (this announcement), HH-GG25-001Cà003C, and HH-GG25-006C, and HH-GG26-031Cà032C.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 1

 

The Golden Gate North deposit currently has a northeast-southwest strike length of approximately 500m and has a true width of approximately 200m. It is open-ended along strike and at depth.

 

Drill log geological, geochemical, and assay data support Golden Gate North being a Reduced Intrusive Related deposit, the same type of deposit as Perpetua’s Stibnite mine development located 12 kilometres east of Golden Gate North.

 

Further assay results for the remaining holes drilled at Golden Gate North are expected in due course.

 

Resolution Minerals Ltd (ASX: RML; NASDAQ: RML) (“Resolution” or the “Company”) is pleased to report receipt of very positive gold assays for three drill holes of the 2026 drill program, HH-GG26-033C, HH-GG26-034C and HH-GG26-035C. These holes were drilled at the Golden Gate North Prospect (“Golden Gate North”) located in the northwestern part of the Company’s Horse Heaven Antimony-Tungsten-Gold-Silver Project, Idaho, USA (Figure 1).

 

HH-GG26-033C, HH-GG26-034C and HH-GG26-035C are located in the south-central part of Golden Gate North, within the known zone of gold mineralisation (Figure 3). As such, the northeast-southwest strike length and width of Golden Gate North are unchanged, at approximately at 500m x 200m. Notwithstanding this, the new gold intersections greatly enhance this emerging gold-tungsten deposit by adding strong continuity to the central part of the deposit with consistently higher gold grades.

 

Detailed descriptions of HH-GG26-033C, HH-GG26-034C and HH-GG26-035C are provided in Appendix A.

 

Continued review of the geological data (from the drill logs), confirms that Golden Gate North has characteristics of a Reduced Intrusive Related Gold-Tungsten deposit. The Company has maintained that Perpetua’s Stibnite deposit is a valid exploration analogue for the prospects at Horse Heaven (Golden Gate and Antimony Ridge). The entirety of recent geological and assay data strengthens the Stibnite analogue.

 

 

Figure 1: Resolution’s Horse Heaven Antimony-Tungsten-Gold-Silver Project

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 2

 

Summary Drill Hole Assay Results

 

Gold assay results reported in this announcement are from the three fanned drill holes at Golden Gate North, HH-GG26-033C, HH-GG26-034C, and HH-GG26-035C. These holes are located in the south-central part of the Golden Gate Deposit (Figure 3). Best gold grade intercepts (Figure 2) from these holes include:

  

HH-GG26-033C:

 

234.8 metres (770 ft) @ 0.62 g/t gold (Au) from 18.3m downhole, including

 

§33.3 m (109 ft) @ 1.53 g/t Au from 213.5m.

 

HH-GG26-034C:

 

272.2 metres (893 ft) @ 0.55 g/t Au from surface downhole, including:

 

o7.4 m (24 ft) @ 1.26 g/t Au from 114.0m

 

o23.1 m (75 ft) @ 1.38 g/t Au from 167.1m

 

o32.1 m (105 ft) @ 1.01 g/t Au from 215.0m

 

HH-GG26-035C:

 

264.9 metres (870 ft) @ 0.59 g/t Au from surface downhole, including:

 

o19.4 m (64 ft) @ 0.90 g/t Au from 156.0m, including:

 

§6.1 m (20 ft) @ 1.39 g/t Au from 169.3m

 

§39.0 m (128 ft) @ 1.53 g/t Au from 199.1m, including:18.7 m (61 ft) @ 2.19 g/t Au from 219.5m, and

 

§13.1 m (43 ft) @ 1.22 g/t Au from 245.7m

 

For the complete set of gold and silver data for HH-GG26-033C, HH-GG26-034C, and HH-GG26-035C, refer to Appendix C.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 3

 

All reported intervals are downhole lengths and do not necessarily represent true widths.

 

The presence of alteration, silicification, quartz veining and visible pyrite is based on geological observations and does not indicate economic mineralisation.

 

   

 

Figure 2 LEFT: Cross section for HH-GG26-035C; RIGHT: Cross section for HH-GG26-033C and HH-GG26-034C. Gold assays in red and yellow. The cross sections show steep east dipping gold mineralisation relating to, and controlled by shears, that display similar geometries. The location of the cross sections is shown in Figure 3.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 4

 

 

Figure 3: Resolution’s Golden Gate North – Location of 2026 and 2025 drill programs with reported drill hole gold assays for drill holes in 2026 and 2025 as histograms (red) and location of the cross sections in Figure 2, with interpreted gold mineralised zone (pale yellow) and interpreted fault/shear zones. Note the zone is open ended to NE and SW, with a gold-in-soil anomaly extending a further 500m to the north (indicated by large arrows).

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 5

 

Drill holes HH-GG26-033C, HH-GG26-034C, and HH-GG26-035C intersected variably sheared and faulted Cretaceous granodiorite of the Idaho Batholith (Figure 2). Core logging, conducted onsite during the program, identified pervasive alteration consists of weak to strong silicification with sericite-pyrite alteration of mafic minerals, and sericite-clay alteration of feldspars. Pyrite occurs as a replacement of primary minerals and within quartz-pyrite veins and shear seams. Vein density and pyrite content generally increase within the more intensely deformed and silicified intervals, supporting the interpretation that the Golden Gate Shear Zone provided a pathway for hydrothermal fluids.

 

Gold mineralisation appears to be present with arsenopyrite and pyrite in quartz veins and in gouge shear zones in each drill hole. Anomalous silver assays appear to be associated with base metals.

 

Importance of Results

 

Continuity of Gold Mineralisation at Golden Gate North

 

Drill holes HH-GG26-033C, HH-GG26-034C and HH-GG26-035C were drilled north of HH-GG25-006C, HH-GG26-031C, and HH-GG26-032C; and south of HH-GG25-001C, HH-GG25-002C, and HH-GG25-003C (Figure 3). The new holes show strong continuity of gold mineralisation in the south-central part of the Golden Gate North Prospect.

 

Previously announced drill hole results immediately north and south of HH-GG26-033C, HH-GG26-034C and HH-GG26-035C include:

 

HH-GG25-001C: 197.5m @ 1.26g/t gold from 34.0m (open ended);

 

HH-GG25-002C: 265.2m @ 0.60g/t gold from surface (open ended);

 

HH-GG25-003C: 253.0m @ 1.50g/t gold from surface (open ended);

 

HH-GG25-006C: 133.7m @ 0.55g/t gold from 376.5m (open ended);

 

HH-GG26-031C: 324 metres @ 0.49g/t Au from surface (open ended);

 

HH-GG26-032C: 322 metres @ 0.37g/t Au from surface (open ended).

 

Refer to the following past ASX Announcements, 28 October 2025, 3 November 2025, 17 February 2026, and 26 October 2026 respectively, for details of these gold intersections.

 

Drill Holes HH-GG26-033C, HH-GG26-034C and HH-GG26-035C show the same down-hole gold distribution patterns as holes HH-GG26-031C and HH-GG26-032C. The holes have a higher-grade lens at depth on the footwall side of the Golden Gate Shear Zone (Figures 2 and 4). They also show oxide zoning with moderate gold grades on the hanging wall side of the shear nearer to the surface.

 

Scalability at Golden Gate North

 

The gold mineralisation at Golden Gate North is currently open ended, extending over a strike length of approximately 500 metres (1,600ft) in the northeast-southwest orientation. The gold envelope has an estimated true width of approximately 200 metres (650ft). Mineralisation has been intersected vertical depths of approximately 300 metres (990ft) (Figures 2 and 4).

 

The drill hole results received to date for Golden Gate North combined with the soil geochemical gold anomaly show that Golden Gate North remains open to the northeast and southwest (Figure 5).

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 6

 

Confirmation of Reduced Intrusive Related Gold Deposit Exploration Model

 

The results of drill holes HH-GG26-033C, HH-GG26-034C, and HH-GG26-035C are consistent with all previous drill holes at Golden Gate (including Golden Gate North and South). The data obtained through the 2025 and 2026 drill programs, including, but not limited to, geology, structure, alteration, and mineralisation (gold, tungsten, sulphides) supports the conclusion that a Reduced Intrusive Related Gold-Tungsten Deposit occurs at Golden Gate. The corollary of the proximity of Golden Gate North, Golden Gate South, and Antimony Ridge, is that they are part of a single large Reduced Intrusive Related Gold-Tungsten-Antimony System.

 

 

Figure 4: Resolution’s Golden Gate North – Cross section of two previously reported drill holes with gold assays as histograms in red, overlain on 2025 drillhole HHGG25-006C, with significant gold intervals and interpreted gold mineralised zone. Refer to the past ASX Announcements, 17 February 2026, and 26 October 2026 respectively, for details of HH-GG25-006C, HH-GG26-031C, and HH-GG26-032C.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 7

 

 

Figure 5: Resolution’s Golden Gate North – Location of drill holes for 2026 and 2025 over gold-in-soil geochemistry. The geochemical gold halo seen as orange and pink shading trends NE and SW beyond the limits of the 2025 and 2026 drilling (yellow arrows).

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 8

 

Craig Lindsay, Resolution’s CEO of US Operations, stated: “The assay results continue to strengthen the case for a major zone of gold mineralisation at the Golden Gate North deposit. Increasingly, we are seeing the characteristics of reduced intrusive related gold deposits at Golden Gate. This aligns with our long held view that the neighbouring Stibnite deposit is a valid analogue for Golden Gate North, Golden Gate South and Antimony Ridge, as related components of a single large mineralised system.”

 

Objectives of the 2026 Drill Program

 

The objective of RML’s large 2026 Golden Gate Drill Program was to define the extent of tungsten and gold mineralisation at Golden Gate. The 2026 drill program comprised 42 diamond core holes for a total of 12,236m drilled (or 40,144 ft). Drilling was undertaken at both Golden Gate North and Golden Gate South (Figure 1).

 

All drill holes are angled. The average hole depth of the program was approximately 290m (Appendix B).

 

The goal of this year’s broader exploration program was to advance the Golden Gate Prospect to the stage where an initial mineral resource estimate may be possible. Following receipt of the remaining drill hole assay data, an initial mineral resource model will be calculated. Subject to the completion of said analysis, a Q1 2027 release is anticipated.

 

Pending Assays

 

Assays remain outstanding for 30 drill holes of the 2026 program. These holes targeted gold and tungsten mineralisation at Golden Gate North and at Golden Gate South.

 

Resolution intends reporting tungsten assays separately as the methodology for reporting tungsten assays involves a more complicated, and lengthy, two-step assay process than gold assays. Tungsten is a difficult metal to assay accurately due to its physical properties, including, but not limited to its high density and high melting point. Multiple techniques and processes are used to obtain accurate values.

 

Next Steps

 

Resolution is completing the processing of drill results from the 2026 program, with a further holes to be released as soon as assays are available.

 

In parallel, permitting for the planned 2027 exploration program at both Antimony Ridge and Golden Gate are progressing rapidly, with various field studies nearing completion to feed into the Environmental Assessment process. Drilling planned for 2027, which is currently being permitted, will be focused on testing a 2,000m corridor which connects Golden Gate North and South, testing open-ended mineralisation to the north of Golden Gate North and additional in-fill drilling and a maiden drilling and bulk sampling program at Antimony Ridge.

 

As both the Golden Gate Prospect and the Antimony Ridge have Fast-41 status, RML maintains ongoing cooperative dialogue with the US Government on matters of permitting and project development.

 

Additionally, progress is being made on developing a plan to process existing tungsten stockpiles, and ongoing tungsten and antimony metallurgical test work is advancing.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 9

 

Authorised for release by the Board of Resolution Minerals Ltd.

 

For further information, please contact:

 

  Aharon Zaetz
Executive Director
Resolution Minerals Ltd
M: +61 424 743 098
ari@resolutionminerals.com
Jane Morgan
Investor Relations
Jane Morgan Management
M: +61 405 555 618
jm@janemorganmanagement.com.au

 

Competent Person’s Statement

 

The information in this report that relates to exploration results relating to metallurgy, is based on and fairly represents information reviewed and compiled by Mr Ross Brown BSc (Hons), M AusIMM, Principal Geologist/director of exploration consulting firm, Riviere Minerals Pty. Ltd, who is a Member of the Australasian Institute of Mining and Metallurgy. Mr Brown has sufficient experience, which is relevant to the exploration activities, style of mineralisation and types of deposits under consideration, and to the activity which has been undertaken, to qualify as a Competent Person as defined in the 2012 Edition of the “Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves”. Riviere Minerals is consulting to Resolutions Minerals Limited and consents to the inclusion in this announcement of the matters based on their information in the form and context in which it appears.

 

JORC cross references

 

The Company confirms it is not aware of any new information or data that materially affects the information cross referenced in this announcement and further to “Agreement to Acquire Major US Antimony Project and Placement” on 11 June 2025, “Drilling to Expand Footprint at Horse Heaven” on 8 September 2025, “Exceptional Rock Chip and Soil Results from Antimony Ridge” on 15 September 2025, “Exceptional Rock Chip and Soil Results Update” on 24 September 2025, “Significant Gold Discovery at Horse Heaven Project” on 28 October 2025, “Significant Gold Discoveries Continue at Golden Gate” on 3 November 2025, “Golden Gate Discovery Grows with Multiple Gold Intercepts” on 2 December 2025, “Further Ultra High Grade Antimony and Silver Results” on 14 January 2026, “New Gold Discovery at Golden Gate South” on 9 February 2026, “Gold & Significant Tungsten Mineralisation in Drilling” on 17 February 2026, “Major Drilling Program Planned to Test Golden Gate Scale” on 18 March 2026, “Exceptional Tungsten Grade Identified in Stockpile Material” on 26 March 2026, “Antimony Ridge Model Shows Extensive Vein Swarms” on 10 April 2026, “Antimony Trioxide Produced from Antimony Ridge“ on 14 April 2026, “Tungsten Concentrates Produced from Golden Gate“ on 28 April 2026, ”Tungsten and Gold Drilling Underway and High Gold Recoveries” on 15 May 2026, and “First 2026 Gold and Tungsten Drilling Proving Encouraging” on 21 May 2026, “Drill Program Progressing Well at Horse Heaven” on 1 July2026 and clarified on 13 July 2026, “Major Gold Extension Confirmed at Golden Gate” on 24 August 2026, “Latest Gold Assays Extend Golden Gate Mineralisation” on 15 September 2026 and “Drilling Confirms Extension of Gold Zone at Golden Gate” on 26 October 2026. The Company confirms that the form and context in which the Competent Person’s findings are presented have not been materially modified from the original announcements.

 

Forward Looking Statements

 

This announcement may contain forward-looking statements. These statements relate to the Company’s expectations, beliefs, intentions or strategies regarding the future. These statements can be identified by the use of words like “anticipate”, “believe”, “intend”, “estimate”, “expect”, “may”, “plan”, “project”, “will”, “should”, “seek” and similar words or expressions containing same. These forward-looking statements reflect the Company’s views and assumptions with respect to future events as of the date of this release and are subject to a variety of unpredictable risks, uncertainties, and other unknowns. Actual and future results and trends could differ materially from those set forth in such statements due to various factors, many of which are beyond our ability to control or predict. These include, but are not limited to, risks or uncertainties associated with the acquisition and divestment of projects, joint venture and other contractual risks, metal prices, exploration, development and operating risks, competition, production risks, sovereign risks, regulatory risks including environmental regulation and liability and potential title disputes, availability and terms of capital and general economic and business conditions.

 

Given these uncertainties, no one should place undue reliance on any forward-looking statements attributable to the Company, or any of its affiliates or persons acting on its behalf. Subject to any continuing obligations under applicable law, the Company disclaims any obligation or undertaking to disseminate any updates or revisions to any forward-looking statements in this announcement to reflect any change in expectations in relation to any forward-looking statements or any change in events, conditions or circumstances on which any such statement is based.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 10

 

Appendix A: Geological Detail of Drill Holes HH-GG26-033C, HH-GG26-034C, and HH-GG26-035C

 

Geological Summary of Three Reported Drill holes from Golden Gate North

 

Drill holes HH-GG26-033C, 034C, and 035C were drilled as fan-holes from the same drill platform at the south-central end of a gold mineralised zone at Golden Gate North. All holes intersected variably sheared and faulted Cretaceous granodiorite of the Idaho Batholith. Alteration is widespread and consists principally of weak to strong silicification and sericite-pyrite alteration of mafic minerals, and sericite-clay alteration of feldspars. Pyrite occurs as a replacement of primary minerals and within quartz-pyrite veins and shear seams. Vein density and pyrite content generally increase within the more intensely deformed and silicified intervals, supporting the interpretation that the Golden Gate Shear Zone provided a pathway for hydrothermal fluids. Gold mineralisation appears to be present with arsenopyrite and pyrite in quartz veins and in gouge shear zones in each drill hole. Anomalous silver assays appear to be associated with base metals.

 

Drill hole HH-GG26-033C was drilled from Drill Site 12 nearly perpendicular to the gold bearing Golden Gate Shear Zone at a 300-degree azimuth, -45 degrees to a depth of 305 meters to test the upper shear zone for gold and tungsten mineralization. Drill site 12 is located 150 meters to the east of the historic Golden Gate Tungsten Mine. The drill hole intersected a high angle NE trending altered post mineral dacite dike in the upper 22.23 meters from the collar and in a second 8.0 meter parallel dike from 153.75m downhole. There appears to be vertical, post mineral movement on the second dike, as the footwall gold boundary dike and mineralized zone are offset from the apparent overall dip of the boundary fault as shown in the attached geologic and assay section (Figure 2). The granodiorite of the Idaho Batholith has been sheared and brecciated along the Golden Gate Shear Zone as it crosses the top of Golden Gate ridge in the area around the Golden Gate Tungsten Mine. The shear has strike slip movement amounting to over 2,000 vertical feet of displacement, East side down as well as kilometres of strike slip movement of the two sides of the sheared and broken granodiorite. Late stage igneous activity associated with the caldera complex to the east and northeast of Golden Gate Hill is seen in the andesite, dacite and rhyolite intrusive dikes and sills that are common in the footwall side of the shear and less common on the hanging wall side.

 

Gold, silver, tungsten, antimony and base metals have been deposited in episodes over the lifespan of movement along the Golden Gate Shear within favourable zones of dilation along the shear zone. The drill holes in this announcement are on the western side of the known gold mineralization and are filling in the knowledge about the boundaries and depth of mineralization in the western part of the mineralized zone.

 

The upper 125m to 165 meters of the holes have been oxidized, with most original sulphide minerals turned to iron and manganese oxides. Sulphide dominant mineralization in both quartz veining/stockworks and in clay fault gouge return the highest gold values below that depth.

 

Hole 33 intersected multiple continuous zones of high-grade gold within a long section of anomalous gold grades beginning at 54.5m and continuing to 253.05 m. An interesting oxidized high silver and gold vein at the hanging-wall contact of the gold-mineralized shear (+0.20 ppm Au) occurs from 57.5 to 59.0 m with 1.5 m @ 0.767 g/t Au, 66.5 ppm Ag, 143 Sb. The upper oxidized portion of the shear zone from 68.0-91.0 m depth shows 23 m @ 0.751 g/t Au. The 24.25 meter zone with elevated arsenic XRF readings between 129.5m to 153.75m averaged 0.801 g/t Au.

 

Mineralisation becomes all sulphide below 154.75 meters. The 39.55 meter sheared and weakly pyritic fault gouge between 161.75m and 201.3m averaged 0.361 g/t Au, while the stronger pyrite/arsenopyrite in 213.45m to 246.7m returned 1.531 g/t Au over 33.25 meters. The sharp contact between the gold mineralization was crossed at 253.05 m in hole HH-GG26-033C into barren granodiorite. There was no andesite intercepted in the Golden Gate Shear Zone in this hole.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 11

 

Drill hole HH-GG26-034C was drilled from the same drill platform at the same 300-degree azimuth, at -70 degrees to a depth of 390.1 meters, to test the shear zone at greater depth than had been achieved in the 2025 drill program. The hole was collared in the dacite dike and stayed in the intrusive till 61 meters in depth, where it hit 6.92 meters of granodiorite before entering the dacite dike was cut for another 8.33 meters depth. Below that point the hole stayed in sheared granodiorite to the footwall structure of the Golden Gate Shear. The principle continuous gold-bearing shear zone begins at 31.65 meters and extends to 272.2 meters in this hole. From 31.65m to 178.68 meters, assays average 0.451 g/t Au over 147.02 meters in the oxidized hanging wall section. The sulphide bearing zone from 178.68m to 188.7 meters averages 1.588 g/t Au over 10.02 meters. From 178.68m to 272.2m assays returned 93.52 meters at 0.838 g/t Au, including 215.0m to 247.13m with 32.08 m at 1.09 g/t Au, all within sheared and pyritic granodiorite on the footwall of the shear zone.

 

The footwall fault was hit at 272.2 meters with the andesite dike intersected from 293m to 297 meters.

 

Drill hole HH-GG26-035C was drilled at a 270-degree azimuth, -70 degrees to a depth of 306 meters to test the Golden Gate Shear Zone gold mineralization in an area with no previous core drilling to evaluate if the high-grade gold mineralization on the footwall of the Golden Gate Shear Zone persisted to the west of previous intercepts in holes HH-GG25-001C and 002C. The hole did not intersect the dacite dike seen in the tops of the two holes adjacent and to the east of hole HH-GG26-035C, proving it is a cross-cutting feature striking ENE across the Golden Gate Shear.

 

The continuous gold-bearing zone hanging wall was crossed at 50.14 meters, with thin low grade gold veins to that depth. A silver vein was cut at the contact of the gold horizon as in hole HH-GG26-033C that ran from 27.81m to 34.76 meters, 6.95 meters assaying 0.164 g/t Au and 10.63 ppm Ag. The entire mineralized zone from 50.14m to 264.9 meters, a total of 214.76 meters, assayed 0.671 g/t Au. Higher grade gold zones were intersected from 169.33m to 175.44m, with 6.11 m @ 1.39 g/t Au, and from 219.5m to 232.95m, with 18.73 m @ 2.194 g/t Au. The strongly pyritic sheared fault gouge from 246.9m to 258.8 meters averaged 1.247 g/t Au.

 

The high-grade gold zone in each of these drill holes is located on the footwall of the Golden Gate shear zone and show the zone extends from drill holes HH-GG25-001 through 004C and from holes HH-GG26-030C and 031C recently announced.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 12

 

Appendix B: Drill Hole Locations and Parameters

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 13

 

Appendix C: HH-GG26-0033C GOLD AND SILVER ASSAY RESULTS

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 14

 

Appendix C: HH-GG26-0033C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 15

 

Appendix C: HH-GG26-0033C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 16

 

Appendix C: HH-GG26-0033C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 17

 

Appendix C: HH-GG26-0033C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 18

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 19

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 20

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 21

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 22

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 23

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 24

 

Appendix C: HH-GG26-0034C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 25

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 26

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 27

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 28

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 29

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 30

 

Appendix C: HH-GG26-0035C GOLD AND SILVER ASSAY RESULTS CONT…

 

 

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 31

 

Appendix D: JORC Code, 2012 Edition

Section 1 Sampling Techniques and Data

 

(Criteria in this section apply to all succeeding sections.)

 

Criteria   JORC Code explanation   Commentary
Sampling techniques   ● Nature and quality of sampling (eg cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as limiting the broad meaning of sampling.   ● This announcement provides an update of the Company’s 2026 drill program recently completed at its Horse Heaven Project in Idaho, USA, and contains exploration results of three drill holes with the ID reference HH-GG26-033C, 034C and HH-GG26-035C.
         
    ● Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used.   ● Reported exploration results (data) includes: drill hole type, drill hole location (UTM metric) and drill hole parameters (dip, azimuth, altitude and end of hole data); sample data; assay data; and geological data. Supporting data includes drill collar locations in UTM metric data, together with dip, azimuth, altitude and end of hole data.
         
    ● Aspects of the determination of mineralisation that are Material to the Public Report.   ● Reported assay data is for gold.
         
    ● In cases where ‘industry standard’ work has been done this would be relatively simple (eg ‘reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay’). In other cases more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (eg submarine nodules) may warrant disclosure of detailed information.   ● Please note that the primary data of the core samples (start, finish, interval) were converted from imperial feet measurements to metric metres in this announcement. Note that the operating jurisdiction uses imperial measurement system.
         
        ● The assay data is derived independent professional laboratory services company of submitted core samples from HH-GG26-033C, 034C and HH-GG26-035C.
         
        ● HH-GG26-033C, 034C and HH-GG26-035C are diamond core holes. Sample intervals are contiguous and range in length individually from 2.2ft to 5.2ft (averaging 4.5ft). The samples are half-cut core prepared by industry standard core cutting saw by qualified personnel.
         
        ● Samples were taken for the majority of the hole depth except where rock voids were encountered.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 32

 

Criteria   JORC Code explanation   Commentary
          ●

Geological data is derived from detailed geological and geotechnical logging by qualified personnel.

         
          ●

Drill core sample assay results of the above-mentioned holes are included in this announcement.

         
          ●

References to mineralised intersects are included in this announcement.

         
Drilling techniques   ●

Drill type (eg core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc).

  ●

The Drilled Holes are diamond core drill holes that were drilled by Evolve Exploration Ltd using two Multipower MP1500 modular core rigs providing HQ diamond drill core.

         
        ●

The drill core is oriented. The core orientation method is conducted using the ACTxCore Orientation System.

         
Drill sample recovery   ●

Method of recording and assessing core and chip sample recoveries and results assessed.

  ●

Drill core recovery of the drilled holes has been consistently high (a function of the solid lithologies) approaching 100%. Lower core recovery rates are sometimes observed in fault zones, with the most significant losses usually occurring near the top of the drill hole, close to the collar, with core recoveries of approximately 50% recovery. This lower core recovery represents <1% of the total length of the drill hole.

         
    ●

Measures taken to maximise sample recovery and ensure representative nature of the samples.

     
           
    ●

Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.

     
           
Logging   ●

Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.

  ●

Drill core was logged for lithology, alteration, mineralisation, structure (geotechnical) using oriented core to a level which has enabled preliminary interpretations relating to style of mineralisation, host and thickness. At this stage no Mineral Resource Estimates, mining studies or metallurgical studies are appropriate.

           
    ●

Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc) photography.

  ●

Drill core is also logged for RQD and Core recovery.

           
    ●

The total length and percentage of the relevant intersections logged.

  ●

Drill core is then digitally photographed wet while whole after logging.

             
          ●

The logging, as described above is both quality and quantitative.

             
          ●

100% of the relevant intersections were logged as per above.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 33

 

Criteria   JORC Code explanation   Commentary
Sub-sampling techniques and sample preparation   ●

If core, whether cut or sawn and whether quarter, half or all core taken.

  ●

The HQ core was halved using a diamond core saw and sampled on geological intervals approximating 0.2m to 1.5m in length. The smallest intervals selected to specifically target mineralised veins have used down to 0.2m intervals. The 1.5 metre interval is most commonly applied across the core.

             
    ●

If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry.

  ●

Drill core was halved using an electric powered core saw by RML contract staff who maintain possession of the core at its Antimony Camp facility.

             
    ●

For all sample types, the nature, quality and appropriateness of the sample preparation technique.

  ●

Half-cut core samples were bagged and tagged using bar-coded sample tags and were securely stored prior to shipment at the Antimony Camp facility.

             
    ●

Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples.

  ●

Half cut core samples were transported by RML contractors under lock and key to ALS prep’ lab’ facility in Twin Falls, ID. No third-party shippers were involved in the shipping process; chain of custody forms were exchanged at ALS Minerals in Twin Falls and a copy kept on file. The remaining boxed cut core are kept at a secure locked facility at Antimony Camp, ID.

             
    ●

Measures taken to ensure that the sampling is representative of the in situ material collected, including for instance results for field duplicate/second-half sampling.

  ●

ALS Minerals Twin Falls prep’ lab’ logs in the samples using the sample tag bar codes provided. Samples were then crushed to 70% less than 2mm, rotary split off 250g, pulverise split to better than 85% passing 75 microns.

             
    ●

Whether sample sizes are appropriate to the grain size of the material being sampled.

  ●

All samples were then shipped to ALS Minerals analytical laboratory in Vancouver, British Columbia.

             
Quality of assay data and laboratory tests   ●

The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.

  ●

Gold was assayed by analytical method Au-AA23: Au by fire assay and AAS 30g nominal sample weight.

             
    ●

For geophysical tools, spectrometers, handheld XRF instruments, etc, the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.

  ●

Silver (Ag) analysis was by analytical method ME-ICP61. Multielement analysis was by analytical method ME-ICP61: 34 elements by HF-HNO3-HClO4 acid digestion, HCl leach and ICP-AES. Quantitatively dissolves nearly all elements for the majority of geological materials. Only the most resistive minerals, such as Zircons, are only partially dissolved.

             
    ●

Nature of quality control procedures adopted (eg standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision have been established.

  ●

No geophysical tools, spectrometers, handheld XRF instruments, etc.. were used in the generation of the assay data.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 34

 

Criteria   JORC Code explanation   Commentary
          ●

Certified reference materials (CRM) from an ISO certified supplier were inserted randomly into the sample stream at a ratio of 2%. CRMs were obtained for Meg LLC of Reno, Nevada; two separate CRMs were used for gold: a low grade and high-grade standard.

             
          ●

Blank material was inserted randomly in the sample stream at a ratio of 2%. Blank material is commercially available pea-gravel that has been previously tested for gold concentrations.t.

             
          ● Duplicates samples were collected by quarter cutting the core at randomly selected intervals. Two quarter-cut portions of core were sent for analysis; the remaining half is kept at a secure facility. Core intervals of poor recovery were not used for duplicate samples. Duplicate core samples were inserted into the sample stream at a ratio of 2%.
             
Verification of sampling and assaying   ●

The verification of significant intersections by either independent or alternative company personnel.

  ●

No verification of the “significant intersections” has been completed to date by either independent or alternative company personnel. The company acknowledges the material nature of the results and is planning a program of select verification assays. Such were the immediacy of the results, these verifications were not possible prior to the release of the initial results.

             
    ●

The use of twinned holes.

  ●

The Company is confident that its sample security processes are adequate for the interim period.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 35

 

Criteria   JORC Code explanation   Commentary
·   ● Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.   ● The announcement details drill holes HH-GG26-033C, 034C and HH-GG26-035C. that were drilled on the same platform but were drilled with different directions and dips (Figure 3). By this HH-GG26-033C, 034C and HH-GG26-035C are fanned holes. No holes are twinned (same collar, same azimuth, same dip)..
             
    ● Discuss any adjustment to assay data.   ● Sample results, certificates and results were sent via email to RML site contractors in Antimony Camp where results are analysed and interpreted.
             
          ● No assay adjustments have been carried out.
             
Location of data points   ● Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.   ● The locations of the Drilled Holes were achieved using handheld GPS programmed into the local coordinate system. The accuracy of the GPS is in line with best practice standards.
             
      ● Specification of the grid system used.      
             
    ● Quality and adequacy of topographic control.      
             
Data spacing and distribution   ● Data spacing for reporting of Exploration Results.   ● The assay data spacing of HH-GG26-033C, 034C and HH-GG26-035C, the length and frequency of each sample and the collective coverage of the drill holes are best practise in terms of hole sample representativeness.
             
    ● Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.   ● In terms of geological data spacing associated with the Drilled Holes every metre of these holes was logged, with details of lithology, alteration, mineralisation recorded to sub-metre detail.
             
    ● Whether sample compositing has been applied.       

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 36

 

Criteria   JORC Code explanation   Commentary
Orientation of data in relation to geological structure   ● Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type.   ● The Drilled Holes have a drill direction that is approaching perpendicular to the regional trend (lithologically and structurally) and also approaching perpendicular to the known mineralisation. The purpose of the Drilled Holes was to test the possible extension of known gold and tungsten mineralisation at surface at depth along strike from past drill holes and past surface sample results and to test the occurrence of gold in un-oxidised rocks at depth.
             
    ● If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.   ● Cautionary Note: There is currently insufficient data pertaining to sampling orientation and the local-scale orientation of mineralisation to determine the true width of the gold intervals in these holes. Additional holes in all directions are required to determine whether the gold mineralisation is broadly pervasive or (to various degrees) spatially constrained. For example, if the gold mineralisation is broadly pervasive, then the gold intervals in this announcement are true widths. If the gold mineralisation is spatially constrained, then the gold intervals in this announcement are not true widths. Based in increasing data, the gold mineralisation is interpreted as being broadly pervasive in association with a structurally-controlled repeating host sequence of country-rock granites and fault breccias
             
Sample security   ● The measures taken to ensure sample security.   ● All drill core samples were delivered directly to RML’s geologists on site where they remain under direct supervision at a secure site.
             
Audits or reviews   ● The results of any audits or reviews of sampling techniques and data.   ● The competent person is unaware of the undertaking of audits or reviews for sampling technique and data, other than its own review.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 37

 

Section 2 Reporting of Exploration Results

 

(Criteria listed in the preceding section also apply to this section.)

 

Criteria

  JORC Code explanation   Commentary
Mineral tenement and land tenure status  

●

Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, past sites, wilderness or national park and environmental settings.

  ●

This announcement refers to exploration results regarding drill core at Golden Gate, a project within the one larger project, Horse Heaven project in Idaho USA, comprising seven hundred and twenty-nine (729) U.S. Federal lode mining claims covering 14,580 acres and includes seven hundred and nineteen (719) mining claims and ten lode mining claims referred as the Oberbillig Group.

             
    ● The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.   ●

The competent person understands that the mining claims are all in good standing.

             
Exploration done by other parties   ● Acknowledgment and appraisal of exploration by other parties.   ●

No exploration results reported in this announcement were performed by other parties.

             
Geology   ● Deposit type, geological setting and style of mineralisation.   ●

The project area is dominated by Cretaceous-aged granitic rocks relating to intrusive phases associated with the Atlanta Lobe of the Idaho Batholith. These largely granodiorite rocks have intruded Neoproterozoic-aged metasediments, comprising quartzites (which are dominant) calc-silicates, marble and black shale. The area and broader region is affected by broad regional folding and N-S, NNE-SSW, and NE-SW faults.

             
          ●

Gold, antimony, tungsten and silver mineralisation is associated with hydrothermally altered and fractured granodiorites.

             
Drillhole Information   ●

A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drillholes:

 

o       easting and northing of the drillhole collar

o      elevation or RL (Reduced Level – elevation above

 sea level in metres) of the drillhole collar

o       dip and azimuth of the hole

o       down hole length and interception depth

o       hole length.

 

  ●

The drillhole information for the Drilled Holes is included in a table (Appendix B) with drill collar location data, altitude, dip, azimuth, and end of hole.

    ● If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.      

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 38

 

Criteria     JORC Code explanation     Commentary
Data aggregation methods   ●

In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated.

  ●

In reporting downhole gold intersections results of HH-GG26-033C, 034C and HH-GG26-035C no maximum and minimum truncations or cut off grades were used.

             
    ● Where aggregate intercepts incorporate short lengths of high-grade results and longer lengths of low-grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail.   ●

In reporting downhole gold intersections/intervals, assay results of HH-GG26-033C, 034C and HH-GG26-035C weighted averages were required due to the fact that sample lengths were variant (between 2.2ft and 5.2ft). The sample interval length was multiplied by the sample assay data then divided by the total length of the interval.

             
    ● The assumptions used for any reporting of metal equivalent values should be clearly stated.   ● No metal equivalents were used in this announcement.
             
Relationship between mineralisation widths and intercept lengths   ●

These relationships are particularly important in the reporting of Exploration Results.

  ●

With reference to the Drilled Holes, these holes were drilled close to perpendicular across the prospect-scale orientation of the known mineralisation.

             
    ● If the geometry of the mineralisation with respect to the drillhole angle is known, its nature should be reported.   ●

There is insufficient data pertaining to the gold mineralisation identified the Drilled Holes to allow conclusive statements concerning the sampling orientation and the local-scale orientation of mineralisation. Therefore the true width nature of the reported widths of the mineralisation is not known.

             
    ● If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (eg ‘down hole length, true width not known’).    

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 39

 

Criteria     JORC Code explanation     Commentary
Diagrams   ● Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported These should include, but not be limited to a plan view of drillhole collar locations and appropriate sectional views.   ●

A drill hole location plan and cross section are provided with geolocation information (coordinates, northing and scale bar) showing the locations of the Drilled Holes. Legends are included within each figure (where appropriate) and when additional explanation is required, this is given to the figure caption.

             
          ●

A drill hole location plan and cross section are provided in this announcement to provide a sense of location of the hole in relation: to i) other drill holes; and ii) intersected mineralisation. The cross sections include a geological interpretation

             
Balanced reporting   ● Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high grades and/or widths should be practiced to avoid misleading reporting of Exploration Results.   ●

This announcement is considered to be fair and balanced with respect to the exploration results, being a drilling update.

             
Other substantive exploration data   ● Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples – size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.   ●

There is no other material data associated with the Drilled Holes not mentioned in this announcement.

             
Further work   ●

The nature and scale of planned further work (eg tests for lateral extensions or depth extensions or large-scale step-out drilling).

  ●

The Drilled Holes, subject of this announcement, are part of a large diamond core drill program of 42 holes for 12,236m (40,144 ft), which is now completed.

             
     ● Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.   ● Drill hole results will be released on an ongoing basis.

 

Resolution Minerals Ltd (ABN: 99 617 789 732) 
Address: Level 21, 91 King William Street, Adelaide South Australia 5000
Email: info@resolutionminerals.com
Website: https://resolutionminerals.com/

Page 40

 

Filing Exhibits & Attachments

1 document

Keep reading